5G/2.4GHz Wireless Extender HDMI® Transmitter and Receiver
Model: XF-V8214
Resolution: 4K@60Hz
Function:
● Plug and play, no additional drivers required.
● Supports single display mode and dual display mode.
● Supports WIDI / Miracast / DLNA / Airplay.
● Wireless Transmission distance up to 98ft/30M(unobstructed).
● 2.4G/5Ghz dual band for smooth streaming.
● With Mouse reverse-control function
Installation
1). Take out the antenna and install it on the back of the receiver.
2). Connect the receiver to the display screen through HDMI cable, then start it after pluging the power supply, and the display terminal will display the standby screen of the product;
3). Plug the transmitter into the computer and it will automatically connected, the blue light will keeps on after about 15 seconds, it means the connection is successful, then click the button to cast the screen.
Notice:
The receiver and transmitter are paired by default when leaving the factory. If the screen cannot be successfully projected, please pair the receiver and transmitter manually.
Pairing Instruction
Insert the transmitter into the USB port of the receiver, the red light flashes quickly, after a few seconds the transmitter shows that the light is always on, which means the pairing is successful.
1). Take out the antenna and install it on the back of the receiver.
2). Connect the receiver to the display screen through HDMI cable, then start it after pluging the power supply, and the display terminal will display the standby screen of the product;
3). Plug the transmitter into the computer and it will automatically connected, the blue light will keeps on after about 15 seconds, it means the connection is successful, then click the button to cast the screen.
Notice:
The receiver and transmitter are paired by default when leaving the factory. If the screen cannot be successfully projected, please pair the receiver and transmitter manually.
Pairing Instruction
Insert the transmitter into the USB port of the receiver, the red light flashes quickly, after a few seconds the transmitter shows that the light is always on, which means the pairing is successful.
Specification of Receiver
Specification of Transmitter
| General info (Receiver ) | |
| Dimension L*W*H(mm) | 141.72*108.3*30MM |
| Product Weight | 333.8g |
| Enclosure | Aluminum Alloy, Deep Grey |
| Power | DC12V, 1A |
| Power Consumption | Full load ≤5W |
| Standby consumption | <3W |
| Storage temperature | -20°C ~ +45°C |
| Operating temperature | 0°C ~ +40°C |
| Storage Humidity | 0 to 90% relative humidity, non-condensing |
| Operating Humidity | 0 to 85% relative humidity, non-condensing |
| ESD Protection | Contact discharge: ±4kV; Air discharge: ±8kV |
| Compatible system | Windows 10 or later, 32 & 64 bit Mac OS 10.14 or later Android 9 or later iOS 11 or later |
| Certification | CE/FCC/RoHS |
| Warranty | 12 Months |
| Technical Characteristics(Receiver ) | |
| HDMI out | 3840x2160P60 / 1920x1200P60 1920x1080P60 / 1280x720P60 / 1024x768P60 |
| Audio out | 1*3.5mm AUX port; HDMI:44.1KHz/16bit PCM2.0; |
| USB-C | 1*USB-C , For pairing Tx |
| USB-A | 2*USB-A Connect to touch panel/mouse to control Host; Note:Mac OS is not supported ; Keyboard is not supported |
| Multi-media play (Only avalible for U-disk FAT32/FAT) -Image:jpg/png/bmp -Video:MP4/MKV/TS/AVI Audio:MP3/AAC |
|
| LED | 1.Booting up: Blue LED lights up for few seconds. 2.Blue LED flashing: power-on is completed, waiting for connection. 3.Blue LED static ON : Connection between Tx and Rx is established and ready to cast screen. 4.Red LED static ON: Screen casting is established. |
| RESET | Long press for 5S to reset the device |
| Connection Protocol | WIDI / Miracast / DLNA / Airplay |
| AirPlay | iOS 9.0 or later, Mac OS 10.14 or later |
| Miracast | Android 5.0 or later |
| Google Cast | Not Support |
| Multi-View | 2 |
| Simultaneous Connections | 1 Receiver can pair with 16 transmitters for switching. |
| Video Latency | ≈150ms |
| RJ45 | 100Mb/s , LAN interface |
| Antenna | Receiving Sensitivity: -70dBm |
| Transmission Protocol | IEEE 802.11ac/802.11n |
| Encryption Protocol | WPA2-PSK |
| Frequency band | 2.4G/5GHz(default) |
| Connection Range | 98ft/30M |
| Coding/Decoding | H.264, H.265 |
Specification of Transmitter
| General info (Transmitter) | |
| Dimension | L159×W62×H16.7(mm) |
| Product Weight | 67.1g |
| Enclosure | PC+ABS black |
| Power | DC5V/ 1A(USB-C) |
| Power Consumption | Full load ≤2.5W |
| Standby consumption | <1.8W |
| Storage temperature | -20°C ~ +45°C |
| Operating temperature | 0°C ~ +40°C |
| Storage Humidity | 0 to 90% relative humidity, non-condensing |
| Operating Humidity | 0 to 85% relative humidity, non-condensing |
| ESD Protection | Contact discharge: ±4kV; Air discharge: ±8kV |
| Compatible system | There is no requirement for the system, and the USB-C interface is required to support DP video output function |
| Warranty | 12 Months |
| Technical Characteristics(Transmitter) | |
| Input Resolution | 3840X2160@30Hz/ 2560x1600@30Hz/ 1920x1200@30Hz/ 1920x1080@60Hz/ 1366x768@60Hz / 1280x800@60Hz / 1280x720@60Hz / 1024x768@60Hz |
| Audio | 44.1KHz/48KHz ,16bit ,PCM2.0 |
| USB-C | Power supply/ Audio&video transmission/ Pairing/ Feedback control signals from Receiver |
| Driver/System | Driveless on Windows/ MacOS/ iOS/ Linux No limitation for the system, and the USB-C interface is required to support DP video output function. |
LED |
3.Blue LED static ON : Connection between Tx and Rx is established and ready to cast screen. 4.Red LED static ON: Screen casting is established. Fault: The purple light is constantly on or flashing. If the TYPEC DP signal is not present, the purple light will flash. |
| Video Latency | ≈150ms |
| Antenna | Receiving Sensitivity: -70dBm |
| Transmission Protocol | IEEE 802.11ac/802.11n |
| Encryption Protocol | WPA2-PSK |
| Frequency band | 2.4G/5GHz(default) |
| Connection Range | 98ft/30M |
| Coding/Decoding | H.264, H.265 |
FAQ
- How to use the button on the transmitter panel：
(2) Short press the button, the blue light will light up and the sharing will exit;
(3) When there are multiple transmitter streaming to receiver, long press and hold one of the transmitter button, and the red light will light up and start to share, then other hosts will exit.
2. Logic of sound sharing:
(1) When the receiver receives multi sharing from different host/transmitters, there will be no mixing, and you will only hear the sound of the last shared host on the display;
(2) When the receiver receives multi sharing from different host/transmitter, the sound of the previous sharing will automatically return to the display after the last shared host exits.
3. When and how to pair the transmitter to receiver:
The pairing identification code of the host is unique as factory default. But when any of the following situations occur, it is necessary to pair the keys with the host again.
(1) Software upgrade;
(2) Web settings change;
(3) Add a new transmitter to the connection.
Pairing method:
Insert the key into the USB-C port of the host, and pairing is successful when the red light of the key remains on.
4. The transmitter cannot connect to the receiver:
If the computer is connected to a transmitter and the blue light flashes for a long time, and a dialog box that is currently being connected appears on the screen, but the image/sound cannot be displayed correctly, just simply plug the button into the USB port of the host and pair it again, as FAQ mentioned in the 3rd point above.
5. What will happen if computer be in standby mode?
When the computer enters standby/sleep mode , it cannot project the screen and the button display light is blue.
- Sound lag or Video lag during transmission？
.png)
.png)
